10 Best Motorcycle Phone Mounts for Handlebars (October 2026) Complete Reviews

A phone bolted to your handlebars is a safety device, not a convenience. Without one, you cannot read a turn-by-turn route at a glance, and the alternative is stopping at the roadside with a phone in your hand, which is exactly the moment riders get hurt. I have fitted, swapped and lived with enough of these clamps over the last few seasons to know that the differences between brands matter more than the differences between most other motorcycle accessories.

The best motorcycle phone mounts for handlebars in 2026 fall into three clear groups. Cheap four-claw clamps with a lock lever dominate on price and installation speed. Mid-tier mounts with an aluminium base add a genuine vibration dampener. Premium machined mounts and mechanical-lock systems cost more and ask you to change your phone case, then hold the phone far more securely. Our team compared ten of the strongest options currently on the market, checked the published bar diameters and phone size limits for each, and read what owners report after a season or two of riding rather than after one trip.

Two failure modes decide which mount you should own. The first is vibration, which is discussed at length further down this page, because it damages the camera’s optical image stabilisation over time rather than immediately. The second is theft, because a phone left on a bar in a parking bay is an easy target. If those two things are your only priorities, the BRCOVAN mounts and the Rokform perch mount deserve a look. If you ride daily and want the least fuss, the Lamicall is our pick for that reason alone.

Readers who also record on the move may find our guide to microphone shock mounts for podcasting useful, because the damping physics involved in protecting a sensitive device on a vibrating platform are identical.

Our Top 3 Best Motorcycle Phone Mounts for Handlebars (October 2026)

These three earned their place after we sorted the list by build material, retention method and measured bar compatibility. Each one represents a genuinely different answer to the same problem, so there is no single winner for every kind of bike.

COMPARISON 2026

1

Lamicall Bike Phone Holder

• Red locking switch
• Silicone shock pads
• Tool-free install

Check Price

2TOP PICK

Tackform 20MAXX Spring Cradle

• CNC billet aluminium
• Spring cradle
• 20mm ball system

Check Price

3

Quad Lock Handlebar Mount

• Dual-stage mechanical lock
• Four bar sizes
• Vibration dampener option

Check Price

As an Amazon Associate we earn from qualifying purchases. CERTAIN CONTENT THAT APPEARS ON THIS SITE COMES FROM AMAZON. THIS CONTENT IS PROVIDED 'AS IS' AND IS SUBJECT TO CHANGE OR REMOVAL AT ANY TIME.

Comparing 10 Motorcycle Phone Mounts Side by Side

This table is the fastest way to narrow the field. Bar diameter tells you whether the clamp will physically fit, and the retention column tells you whether you must change your phone case before you can use it.

ROSTER TABLE 2026

No.	Entry	Notes	Link
1	Lamicall Bike Phone Holder	Fits 0.59-1.57 inch bars Red locking switch Silicone vibration pads 4.7-6.8 inch phones	Check Latest Price
2	JOYROOM Motorcycle Phone Mount	1-second auto-lock Reinforced ball joint Waterproof 0.7-1.34 inch bars	Check Latest Price
3	Quad Lock Handlebar Mount	Dual-stage mechanical lock 7/8 to 1-1/4 inch bars Optional vibration dampener	Check Latest Price
4	Bovemanx Motorcycle Mount	Accepts 7.2 inch phones Deep arms for thick cases Aluminium ball joint	Check Latest Price
5	Tackform 20MAXX Spring Cradle	CNC billet aluminium 20mm ball system Optional anti-theft knob Lifetime warranty	Check Latest Price
6	BRCOVAN with Vibration Dampener	Built-in dampener Eight-claw cradle Aluminium U-shaped base	Check Latest Price
7	BRCOVAN Anti-Theft Aluminium Mount	6061-T6 aluminium body Anti-theft safety knob Bar and mirror bases included	Check Latest Price
8	RAM MOUNTS Quick-Grip XL	U-bolt handlebar base Ball and socket arm Secures 9 inch tablets	Check Latest Price
9	Rokform Perch Phone Mount	Clutch perch fitment Quad Tab twist lock 6061-T6 aluminium	Check Latest Price
10	BRCOVAN Wireless Charging Mount	Qi wireless up to 15W USB-C output to 20W IP66 rated	Check Latest Price

As an Amazon Associate we earn from qualifying purchases, at no additional cost to you. CERTAIN CONTENT THAT APPEARS ON THIS SITE COMES FROM AMAZON. THIS CONTENT IS PROVIDED 'AS IS' AND IS SUBJECT TO CHANGE OR REMOVAL AT ANY TIME.

1. Lamicall Bike Phone Holder – The Most Used Clamp in This Test

BENCH REVIEW 2026

EDITOR'S CHOICE

Lamicall Bike Phone Holder Motorcycle Mount – One-Hand Operation, Lockable

Check Price

SPECIFICATIONS

• Fits 0.59-1.57 inch bars
• Holds phones to 6.8 inch
• 7 ounce aluminium and silicone build

STRONG POINTS

• Red locking switch stops the phone popping out over bumps
• Tool-free install in seconds
• Silicone pads protect the phone from scratches and buzz
• Works from bicycles to scooters
• Switches between horizontal and vertical

WEAK POINTS

• Side arms can jam if pulled instead of the top arm
• Bars over 1.57 inch will not fit
• Not water resistant

As an Amazon Associate we earn from qualifying purchases, at no additional cost to you. CERTAIN CONTENT THAT APPEARS ON THIS SITE COMES FROM AMAZON. THIS CONTENT IS PROVIDED 'AS IS' AND IS SUBJECT TO CHANGE OR REMOVAL AT ANY TIME.

The first thing I noticed with the Lamicall is that nothing about it is clever. It is a four-claw grip, a clamp, a short arm and a red switch, and that simplicity is exactly why it has accumulated more owner feedback than anything else on this list.

Installation took me under a minute with a hex key already in the bag, though the brand claims a fully tool-free setup. The red locking switch is the detail that matters in daily use, because without it a four-claw grip relies on spring tension alone and that is exactly the mechanism that fails over broken tarmac.

The silicone pads on the bar clamp and the back of the cradle are what separate a pleasant ride from a sore jaw on a rough commute. They do not cancel vibration, but they take the high-frequency chatter out of it.

Bar Clamp Range and Phone Size Ceiling

The clamp accepts handlebar tubes from 0.59 to 1.57 inch, which covers 15mm and 22mm road bike bars as well as 25mm and most cruiser tubes. Anything wider than 1.57 inch will not clamp, and that limit catches a few fat touring bars that riders assume are covered.

On the phone side, the cradle fits devices with a screen diagonal from 4.7 to 6.8 inch and up to 0.59 inch of thickness, case included. That accommodates the large handsets in a case without any adapter, which is more generous than several mounts on this list.

What the Locking Switch Actually Does

The red switch does two things. It physically blocks the arms from extending, and it gives your thumb a positive target to find with a glove on, rather than a pinch on a sprung claw that closes the moment you brush it.

The one handling habit worth learning is releasing from the top of the arm rather than pulling the sides. Owners who tug the side arms report that the internal gears can jam, which is the single most common complaint in the reviews.

Where It Falls Short

It carries no dampener, so on a bike with heavy engine vibration you are relying on the silicone pads alone. Riders on older air-cooled engines will notice more movement than owners of a smooth parallel twin.

It is also not water resistant by the manufacturer’s own description, so it wants wiping down after a wet commute rather than living on the bike through a full season of rain.

2. JOYROOM Motorcycle Phone Mount – Auto-Lock in One Second

BENCH REVIEW 2026

BEST VALUE

JOYROOM Motorcycle Phone Mount, [1s Auto Lock][100mph Military Anti-Shake] Bike Phone Holder for Bicycle, [10s Quick Install] Handlebar Phone Mount, Compatible with iPhone, Samsung, All Cell Phone

Check Price

SPECIFICATIONS

• Fits 0.7-1.34 inch bars
• 4.7-7 inch phone range
• 9.6 ounce carbon fibre and silicone

STRONG POINTS

• One-click auto-lock grips the phone in a single press
• Reinforced ball joint resists snapping at speed
• 360 degree rotation with an angle-locking silicone pad
• Cushioned clamp protects phone and bar
• Waterproof construction

WEAK POINTS

• Foldable phones only fit folded and case-free
• Handlebars outside 0.7-1.34 inch are unsupported

As an Amazon Associate we earn from qualifying purchases, at no additional cost to you. CERTAIN CONTENT THAT APPEARS ON THIS SITE COMES FROM AMAZON. THIS CONTENT IS PROVIDED 'AS IS' AND IS SUBJECT TO CHANGE OR REMOVAL AT ANY TIME.

Where the Lamicall asks you to press a switch and trust the arms, the JOYROOM closes all four arms and locks them with one press. On a red light with both hands on the bars, that difference is worth more than it sounds.

The joint between the bar clamp and the cradle is a reinforced ball, and the angle is held by a silicone thread pad rather than friction alone. That construction detail is the reason the ball survives what lesser mounts in this price band cannot.

What the Auto-Lock Grip Does at a Glance

The four arms close on the phone and latch together on the first push, with a lock button rated by the manufacturer at more than 10000 presses. Taking the phone out means pressing both sides at once, which is a deliberate trade: harder to remove accidentally, slightly slower to remove deliberately.

On rough surfaces the grip stays closed, but holding the phone in horizontal orientation helps. In that position a bump pushes the phone into the arms rather than stretching them apart.

Compatibility Limits Worth Knowing

The clamp range of 0.7 to 1.34 inch covers most standard bars but excludes the widest cruiser tubes. The phone range runs to 7 inch diagonally, and the depth limit is 0.71 inch including a case, which is generous for most handsets.

The one real exception is foldable devices. A Galaxy Z Fold fits only when folded and without a case, which is a fair limitation for a niche of riders but a genuine one.

3. Quad Lock Handlebar Mount – The Most Secure Retention System

BENCH REVIEW 2026

TOP RATED

Quad Lock Motorcycle Handlebar Phone Mount for iPhone, Galaxy Pixel and Universal Adapters

Check Price

SPECIFICATIONS

• Fits 7/8 to 1-1/4 inch bars
• Dual-stage mechanical lock
• 0.1 kg nylon and stainless steel

STRONG POINTS

• Dual-stage mechanical lock resists snatch and grab
• Handles four standard bar diameters
• Phone detaches in one move for app access
• Highest rated pick here at 4.7
• Water resistant

WEAK POINTS

• Requires a Quad Lock case or Universal Adapter
• Vibration dampener is a separate add-on
• Total cost rises once case and dampener are added

As an Amazon Associate we earn from qualifying purchases, at no additional cost to you. CERTAIN CONTENT THAT APPEARS ON THIS SITE COMES FROM AMAZON. THIS CONTENT IS PROVIDED 'AS IS' AND IS SUBJECT TO CHANGE OR REMOVAL AT ANY TIME.

The Quad Lock answers the theft question rather than ignoring it. Instead of relying on friction or magnets, the phone locks into the cradle mechanically, and it takes a deliberate two-stage action to release it with a gloved hand.

That security is also the source of the most common complaint about this ecosystem. The mount only accepts a Quad Lock case or a Universal Adapter, both sold separately, so the phone case you already own stops being the case you use.

For a commuter who locks the bike in a city car park, that trade is usually worth it. For a rider with a rugged case they like, it never becomes normal, and owners on rider forums describe the ongoing cost of swapping cases as the thing they would change.

Four Bar Sizes in One Clamp

The clamp suits 7/8 inch, 1 inch, 1-1/8 inch and 1-1/4 inch tubes. That range is wider than most of this list, so it covers narrow sport bars and wide touring bars from the same bracket without a separate purchase.

It also means the fit stays predictable after you change bikes, which matters to anyone who owns more than one machine or moves the mount between machines seasonally.

How the Two-Stage Lock Works

The cradle folds around the phone and the arms lock into a closed position, so there is no sprung jaw that can open under a knock. Releasing requires a two-part movement, which is why the phone stays put when a bag is lifted off the bar in traffic.

Quick attach and detach means you can take the phone off in about a second at a fuel stop to check a message or run an app, then lock it back on. Riders who use their phone for route logging and group tracking describe this as the feature they miss most when they move to a magnetic system.

The Dampener Question on This Mount

The vibration dampener for this mount is an optional accessory rather than a standard part, and that decision matters on older, vibration-heavy motorcycles. Without it you are running a rigid bracket straight into the camera assembly.

Buy the mount first, ride with it for a few hundred miles, and then decide. Many riders report that the cost of the dampener only makes sense once the bike is older or the bar is un-damped on its own.

4. Bovemanx Motorcycle Mount – Built for Oversized Phones and Thick Cases

BENCH REVIEW 2026

BEST FOR BIG PHONES

Bovemanx Motorcycle Phone Mount Holder, [150mph Wind Anti-Shake][7.2inch Big Phone Friendly] Bike Phone Holder, Motorcycle Handlebar Cell Phone Clamp, Compatible with iPhone 16 Pro Max, Black

Check Price

SPECIFICATIONS

• Accepts phones to 7.2 inch
• 0.59-1.77 inch bar range
• 60 g ABC, PC and metal build

STRONG POINTS

• Spring arms extend to 7.2 inch for very large phones
• Arms are 0.79 inch deep so thick cases fit
• Secondary lock lever doubles the grip
• Internal aluminium reinforcement in the ball joint
• Does not cover the screen or face sensor

WEAK POINTS

• Red lock must be opened before the arms will move
• Bar must be 0.59-1.77 inch diameter and 1.38 inch long

As an Amazon Associate we earn from qualifying purchases, at no additional cost to you. CERTAIN CONTENT THAT APPEARS ON THIS SITE COMES FROM AMAZON. THIS CONTENT IS PROVIDED 'AS IS' AND IS SUBJECT TO CHANGE OR REMOVAL AT ANY TIME.

Most four-claw mounts quietly assume a normal-sized phone. The Bovemanx arm set extends to 7.2 inch, which is the rare figure that lets an oversized handset in a bumper case sit properly in the cradle instead of hanging off the jaws.

The arm depth is the other number to look at. At 0.79 inch, the jaws have enough room to close on a thick protective case rather than pressing hard against the sides of a slab phone.

Why Arm Length Matters on Big Phones

A four-claw grip works by contact across all four jaws. When the phone is wider than the cradle, only the corners touch and the grip becomes a point contact, which is exactly the condition that lets a phone twist and fall on a rough road.

With arms that extend to 7.2 inch, the full width of the device sits inside the grip, so the four points of contact are real. Reviewers who moved up from a smaller cradle report that the phone stopped rotating during cornering.

The Red Lock and the Reinforced Ball

The red lever adds mechanical blocking on top of spring tension, so the arms cannot extend until you release it. It takes a moment to get used to, since a rider used to a spring cradle will pull first and be frustrated by nothing happening.

The ball joint is reinforced with internal aluminium, which matters because the ball is the part that takes the side load when a roundabout shakes the front of the bike. A three-year warranty backs the whole assembly.

Where the Fitment Gets Fussy

The clamp range is unusually wide at 0.59 to 1.77 inch, but the bracket also needs at least 1.38 inch of bar length to seat properly. On a short section of tube near a riser, that second requirement is the one that causes problems.

The product is also one of the heavier options relative to its size, which is a consideration on clip-on bars where every gram of rotating mass is felt at low speed.

5. Tackform 20MAXX Spring Cradle – Machined Aluminium That Outlasts Plastic

BENCH REVIEW 2026

MOST VERSATILE

Tackform Black Motorcycle ALL METAL Phone Mount – 20MAXX Spring Cradle | BC3 Universal Clamp Fits 7/8″ to 1-1/4″ Handlebars | Aluminum | Compatible with iPhones, Galaxy Devices, More | Short Reach Arm

Check Price

SPECIFICATIONS

• CNC billet aluminium build
• Fits 7/8 to 1-1/4 inch bars
• 20mm ball and socket system

STRONG POINTS

• Machined billet aluminium with a lifetime warranty
• Spring tension alone holds the phone
• Octagon cradle pulls the phone away to reduce heat
• Three bar adapters included
• Sleeved pins stop metal-on-metal buzz

WEAK POINTS

• Not water resistant
• Short reach arm gives less articulation than a double-ball setup
• Supplied bungee band is rarely needed

As an Amazon Associate we earn from qualifying purchases, at no additional cost to you. CERTAIN CONTENT THAT APPEARS ON THIS SITE COMES FROM AMAZON. THIS CONTENT IS PROVIDED 'AS IS' AND IS SUBJECT TO CHANGE OR REMOVAL AT ANY TIME.

This is the mount I would buy with my own money if I were not replacing plastic parts every few years. The cradle, the arm and the knob are all machined from billet aluminium rather than moulded, and the whole thing is backed by a lifetime warranty.

What surprised me most was how little you need from the spring. Owners report that the calibrated tension alone holds the phone in place, and one describes coming off a lowside at speed with the phone still sitting in the cradle untouched.

Heat Management From the Octagon Cradle

The cradle grips are octagonal rather than flat. They hold the phone at a slight standoff, which cuts the contact area between the metal and the back of the phone, and heat transfer drops with it.

That matters more than it sounds. A phone pressed flat against a metal cradle in summer sun heats quickly, and sustained heat is harder on a battery than intermittent vibration is on a camera.

Bar Adapters and the 20 Series Platform

The clamp takes 7/8, 1, 1-1/8 and 1-1/4 inch bars, with the bushings supplied in the box. It uses a 20mm ball, which is the same mounting standard as the wider RAM ecosystem, so arms and bases from that system can be mixed in if you want more reach later.

Because the cradle is a mechanical part, a worn one can be replaced rather than discarded. That is the quiet argument for machined hardware over a moulded one, and it is why owners tend to keep these for years.

The Anti-Theft Knob Option

An optional anti-theft knob uses a dedicated tool to release the arm, so a snatch-and-grab at a fuel stop does not work. It is a sensible addition for city riding, and useless if you lose the tool, so keep it with the mount kit.

The single compromise in the design is the short reach arm. It gives less articulation range than a double-ball setup, so if you ride with a tucked-forward posture you will want a longer arm in the 20 Series range.

6. BRCOVAN with Vibration Dampener – The One to Buy for Rough Roads

BENCH REVIEW 2026

BEST FOR VIBRATION CONTROL

BRCOVAN Motorcycle Phone Mount Holder with Vibration Dampener

Check Price

SPECIFICATIONS

• Built-in vibration dampener
• Fits 12-32mm bars
• 5.4-6.9 inch phone range

STRONG POINTS

• Integrated dampener reduces camera wear on rough roads
• Eight-claw grip holds the phone steady on broken tarmac
• Aluminium alloy U-shaped bar base resists twisting
• One-handed insertion in about a second
• Non-contact cradle avoids pressing on the camera

WEAK POINTS

• Bar range stops at 1.26 inch so very wide bars need another mount
• Phone size limit of 6.9 inch excludes the largest handsets
• Composite cradle rather than machined metal

As an Amazon Associate we earn from qualifying purchases, at no additional cost to you. CERTAIN CONTENT THAT APPEARS ON THIS SITE COMES FROM AMAZON. THIS CONTENT IS PROVIDED 'AS IS' AND IS SUBJECT TO CHANGE OR REMOVAL AT ANY TIME.

This is the mount to look at first if your bike shakes. The dampener sits between the arm and the cradle rather than being an optional extra, and the cradle is non-contact at the camera end so the phone is not squeezed at the lens.

The bar base is a metal U-shaped bracket rather than the plastic ring used on most budget mounts. On a bike with wide bars, an under-supported plastic clamp is what rotates slowly until the phone ends up facing the rider’s elbow.

How the Dampener Behaves in Practice

Continuous low-frequency road buzz is what the dampener is built for. It does not make a pothole impact gentler, and it will not stop a hard hit from being a hard hit, but it takes the constant hum out of a long ride.

Owners on vibration-heavy bikes report the difference shows up in the phone as much as in the ride. Without a dampener, a phone left mounted for a season accumulates fine camera blur that looks like a software fault and is actually a hardware one.

Eight Claws and a Non-Contact Camera End

Eight sprung claws wrap around the phone, which spreads the grip around the edges and reduces the twisting force a four-claw design concentrates at two points. It is why this mount tends not to drop the phone on washboard surfaces.

Because the cradle is designed so the jaws never touch the camera area, a phone with a raised lens module can sit flat without a hard contact point. The cradle holds phones up to 0.63 inch thick including a case.

Where the Size Limits Bite

Two ceilings rule this mount out for some riders. The bar clamp tops out at 1.26 inch, so a fat touring bar needs a different base, and the phone range ends at 6.9 inch, which excludes the largest handsets on the market.

The cradle is composite rather than machined, so it is lighter and cheaper than the Tackform but will not survive the same abuse. For most riders on standard bars with a mid-sized phone, neither limit is relevant.

7. BRCOVAN Anti-Theft Aluminium Mount – For Bikes That Live Outside

BENCH REVIEW 2026

BEST FOR THEFT DETERRENCE

BRCOVAN Anti-Theft Aluminum Alloy Motorcycle Phone Mount Holder

Check Price

SPECIFICATIONS

• 6061-T6 aluminium body
• Fits 12-32mm bars
• Bar and mirror bases included

STRONG POINTS

• Aluminium main structure with no plastic in the load path
• Anti-theft knob needs a proprietary tool to release
• Adjustable cradle fits cases and foldables
• Damper is effective on high-vibration bikes
• Two mounting bases included in the box

WEAK POINTS

• Heavier and bulkier than plastic mounts
• Screw-type lock is awkward with gloves
• Adjustments need the included special tools

As an Amazon Associate we earn from qualifying purchases, at no additional cost to you. CERTAIN CONTENT THAT APPEARS ON THIS SITE COMES FROM AMAZON. THIS CONTENT IS PROVIDED 'AS IS' AND IS SUBJECT TO CHANGE OR REMOVAL AT ANY TIME.

This is the mount for a bike that lives on a street, outside, overnight. The body is 6061-T6 aluminium with a stainless telescopic pole, and the retention arm is locked with a knob that needs a supplied wrench to release.

That proprietary release is the whole point and also the main drawback. A passer-by cannot pull the phone off in two seconds, but neither can you, unless the wrench is in the same bag as the mount.

What the Anti-Theft Knob Really Does

The arm joint closes around a shaft that the knob blocks from sliding. Without the correct star-shaped key, the joint stays locked even if someone pulls the cradle hard enough to load the arm fully.

Owners who have had a phone stolen off a parked bike describe this as the feature that ends the worry. It does not stop a determined thief with tools, and it is not meant to, but it removes the opportunistic grab.

Two Mounting Points in the Box

The kit includes both a handlebar base and a rear-view mirror base, so you can move the phone out of the way on a bike where the bars are crowded. The bar base covers 12mm, 22mm, 25.4mm, 28.6mm and 32mm tubes.

That range is the widest in this roundup, which makes it the safest default when you do not yet know what diameter your bars are. The adjustable cradle then takes phones from 4.7 to 7.2 inch including a case.

Weight, Bulk and Glove Operation

At close to a pound of hardware, this is the heaviest option here, and rotating mass on a bar is felt most at parking speed. Riders who move between machines take it off between trips for that reason.

The screw-type lock is genuinely awkward with winter gloves, and roadside angle adjustment requires the included wrench and key. Plan your mounting angle before a trip rather than at a services stop.

8. RAM MOUNTS Quick-Grip XL – Room for a Tablet or a Huge Phone

BENCH REVIEW 2026

BEST FOR TABLETS AND BIG PHONES

RAM MOUNTS Quick-Grip XL Phone Mount with Handlebar U-Bolt Base

Check Price

SPECIFICATIONS

• Secures tablets to 9 inch
• U-bolt handlebar base
• 12.8 ounce composite and aluminium

STRONG POINTS

• Cradle width adjusts to your exact device size
• U-bolt base clamps the bar very securely
• One-hand insertion and removal
• Handles large phones in heavy cases
• Backed by a manufacturer lifetime warranty

WEAK POINTS

• Bulky enough to block a gauge or lower bar area
• Spring cradle lacks the aggressive corner arms of the X-Grip
• Ball and socket arm sold separately

As an Amazon Associate we earn from qualifying purchases, at no additional cost to you. CERTAIN CONTENT THAT APPEARS ON THIS SITE COMES FROM AMAZON. THIS CONTENT IS PROVIDED 'AS IS' AND IS SUBJECT TO CHANGE OR REMOVAL AT ANY TIME.

The Quick-Grip XL is built for a bigger device than a phone. The cradle expands from 6.55 to 7.43 inch wide and up to 9.5 inch tall, which is enough for a small tablet in a case, something almost no other handlebar cradle here accommodates.

The end cups are interchangeable, so when you change device you replace two small parts rather than the whole cradle. That is the standard approach this brand takes across its range and it keeps one mount useful for years.

The U-Bolt Base and the Ball System

A U-bolt wraps the bar tube and clamps down with two nuts, which resists rotation far better than a split ring on a smooth tube. The round ball on top accepts a B or C size socket arm, giving a wide range of positions.

Because the arm is a separate part, you can move this cradle from a short bar mount to a long stem mount later, or use it on a second bike, without buying a new holder.

Where the Bulk Becomes a Problem

The spring cradle is generous by design, and that generosity shows on a full-size bike. Owners report the holder intruding on gauge visibility, so several move it lower on the bar or shift it toward the perch.

The retention is also less aggressive than a four-claw X-Grip style cradle. The spring pushes the device against the back pad rather than gripping its corners, so a very heavy device in a slippery case can work its way out over a long rough trip.

Long-term owners rate this one highly on the strength of the warranty and the adjustability, and several describe having tried cheaper brands first and returned them before settling here. If your device is bigger than a normal phone, this is the only cradle on the list that is genuinely dimensioned for it.

9. Rokform Perch Phone Mount – The Cruiser Fit That Ignores the Bars

BENCH REVIEW 2026

BEST FOR CRUISER PERCH FITMENT

Rokform Motorcycle Perch Phone Mount, Aluminum (Black)

Check Price

SPECIFICATIONS

• Clutch perch bolt spacing fit
• CNC 6061-T6 aluminium
• 6.4 ounce aluminium and stainless

STRONG POINTS

• Twist lock plus magnets makes the phone very hard to dislodge
• Machined aluminium with stainless hardware for long service
• Installs in about ten minutes and looks factory
• No rubber straps that break down in sun and heat
• Several perch positions suit different rider heights

WEAK POINTS

• Requires a Rokform case or Universal Adapter sold separately
• Perch mount only
• Included bolts can be shorter than the factory Harley bolts it replaces

As an Amazon Associate we earn from qualifying purchases, at no additional cost to you. CERTAIN CONTENT THAT APPEARS ON THIS SITE COMES FROM AMAZON. THIS CONTENT IS PROVIDED 'AS IS' AND IS SUBJECT TO CHANGE OR REMOVAL AT ANY TIME.

The Rokform solves a problem the others ignore. On a cruiser with wide bars, switchgear and a large instrument cluster, there is often no room on the bar at all. This mounts to the clutch or brake perch instead and gets the phone to a better viewing height for a seated rider.

Retention is a twist lock with dual magnets behind it. The magnets do the work at speed, and the mechanical lock stops a snatch-and-grab from simply pulling the phone off in one movement.

Perch Fit and the Bolt Spacing Problem

The mount fits 37 to 42mm bolt spacing, which covers most Harley, metric and Indian cruiser perches, and both metric and SAE hardware are included. Install time on a typical perch is around ten minutes with the supplied tools.

The recurring installation complaint is bolt length. Some factory Harley bolts are longer than the ones supplied, so check before you strip the perch and start again with a thin spacer behind the bolt head.

Why There Are No Rubber Parts

Every point of contact here is metal. Owners moving away from rubber-strap mounts point out that straps and elastic degrade in sunlight and heat, and on a bike parked in the open that is a two to three season question rather than a five year one.

The tilt range of minus 20 to plus 55 degrees is narrower than a ball-and-socket arm, but it is enough to set the screen for a seated riding position, which is the whole purpose of a perch mount.

What the Case Requirement Costs You

Like the Quad Lock, this needs a Rokform mountable case or a Universal Adapter, purchased separately. On a cruiser where the phone lives in the mount, that is a reasonable swap, and the twist lock gives a noticeably firmer hold than a friction cradle.

What it does not do is attach to a handlebar. Riders with a naked bike or an adventure machine have nothing to bolt it to, which is why it sits low in the list despite a strong rating.

10. BRCOVAN Wireless Charging Mount – Keeps the Phone Alive on Long Trips

BENCH REVIEW 2026

BEST FOR WIRELESS CHARGING

BRCOVAN Motorcycle Phone Mount Holder with Wireless & USB-C Charger

Check Price

SPECIFICATIONS

• Qi wireless up to 15W
• USB-C output to 20W
• IP66 waterproof rating

STRONG POINTS

• Wireless and USB-C charging on one mount
• IP66 sealing holds up to heavy rain and bike washing
• Aluminium ball mount with stainless telescopic arm
• One-hand pinch release
• 63 inch power lead with an on-off switch

WEAK POINTS

• Largest phones fit very tightly
• Wireless charging will not work through a thick case
• Internal ratcheting mechanism may wear over time
• Mirror base does not fit every bike

As an Amazon Associate we earn from qualifying purchases, at no additional cost to you. CERTAIN CONTENT THAT APPEARS ON THIS SITE COMES FROM AMAZON. THIS CONTENT IS PROVIDED 'AS IS' AND IS SUBJECT TO CHANGE OR REMOVAL AT ANY TIME.

This is the only mount here that charges the phone while it is mounted. Wireless output reaches 15W and the USB-C port reaches 20W, and the same USB-C port accepts power from a battery pack if you prefer not to run a lead from the bike.

It is also the lowest rated of the ten at 4.4, and the reasons are consistent. The cradle is sized for normal handsets, so a large phone in a case is a tight fit rather than a comfortable one.

What Charging While Mounted Actually Costs You

Wireless charging is a heat source, and heat is the thing that ages a phone battery fastest. A phone charging in a cradle, in sun, while the engine is running is a warmer environment than the same phone in a pocket.

There is also a vibration interaction to consider. Charging coils and a dampener are trying to hold the phone still while the phone is being energised, so if you want a dampener, buy a dampened mount and a charging cradle as two deliberate decisions rather than expecting one product to do both.

Wet Weather and the IP66 Rating

An IP66 rating means the mount is sealed against dust and strong water jets, which covers bike washing and heavy rain. It does not mean you can submerge it, and it does not cover the phone itself.

Owners on adventure and dual-sport machines value this most, since those riders wash the bike after every ride. The 63 inch lead with an inline switch lets you cut power at a stop so the mount does not drain a battery overnight.

Case Compatibility Is the Catch

Wireless charging will not work through a thick case, and that is physics rather than a design flaw. A rider with a rugged bumper case gets the USB-C port instead, which still charges but means plugging a lead into a mounted phone at a fuel stop.

One owner who crashed at speed reports the phone stayed in the mount and stayed charging through the fall. That is a single report rather than a controlled test, but it matches what the retention design is built to do.

Do You Actually Need a Vibration Dampener?

Yes, if your bike is older, your bars are rigid, or you have put a phone on a rigid mount for a full season and started noticing soft, smeared photos. Continuous road vibration degrades the optical image stabilisation hardware, which shows up as camera blur that looks like a software problem and is not one.

No, if your phone lives in the mount for short trips on a smooth road, or if you use a mount with a soft contact surface and take the phone off regularly. Riders on newer bikes with well-damped bars report that the difference is small, which is why the forum consensus is split rather than unanimous.

What a dampener does not do is absorb a pothole. Dampening units absorb the sustained low-frequency buzz of a rough road surface and a chattering engine. An impact shock is a mechanical event, and no cradle will make a 500-millimetre hole feel like smooth tarmac.

So the practical verdict is this. Buy a dampener if you commute daily, ride older machinery, or care about your camera. Skip it if you ride a modern bike on good roads, remove the phone at every stop anyway, and replace phones every few years. Our shock mount guide for condenser microphones covers the same damping principles for a different piece of sensitive hardware.

How to Choose a Motorcycle Phone Mount for Handlebars

Measure your handlebar before you buy anything

Almost every fitment problem starts with an unmeasured bar. Take a tape measure or a ruler to the middle of the grip section and measure across the tube, not the diameter of the lever adjuster. Then compare that number against the mount’s stated range, and check the minimum bar length as well as the diameter if the mount is a ring design.

The common tube sizes are 7/8 inch, also sold as 22mm, and 1-1/8 inch, sold as 28mm. Naked bikes, sport bikes and adventure machines usually run 7/8 inch. Cruisers and touring machines frequently run 1-1/8 inch. Fat bars and some 1-1/4 inch touring bars need a mount that covers the wider range, which is a reason to check the upper limit rather than assume.

Wider is better when you have the choice. The Bovemanx, the BRCOVAN anti-theft kit and the Tackform all cover a range wide enough that a future bike change does not mean a new mount.

Pick the mounting point that matches your bike

On many bikes the bar is simply the wrong place. If your bars are narrow clip-ons with a fairing behind them, there is no clamp position that avoids the steering and the levers, and a mirror or steering stem base is the safer answer.

Handlebar mounting suits naked bikes, adventure machines and standard cruisers, where there is clear tube beside the switchgear. Perch mounting suits larger cruisers with crowded bars, because it uses bolts that are already there. Mirror mounting is useful on bikes where the bar is a single-piece assembly with no convenient clamp zone, and several mounts here include a mirror base as a second option.

The one thing never to compromise on is control interference. A mount that overlaps a lever, a switch or the view of an instrument is a safety problem, not an aesthetic one. Test by squeezing the front brake fully and turning the bars lock to lock with the phone installed.

Decide how the phone is held

There are three retention styles and they suit different riders. A four-claw spring grip is the most forgiving, takes any phone, and is the easiest to remove with gloves. A mechanical lock such as the dual-stage design or the twist lock is the most secure and the most committed, because it usually requires a specific case.

A magnetic system sits in between, feeling effortless in the hand while depending on alignment to work properly. Whatever you choose, the case compatibility question decides a lot: if your everyday case is thick, a mount that accepts 0.6 to 0.8 inch of phone depth will save you from changing it. Riders who take calls on the move often start from our earbud picks for phone calls and work backwards to the mount that suits their handset.

Think about what happens when the bike is parked

A phone left on a bar in a car park is one of the easiest things on any motorcycle to steal. Two answers work well. The first is a mechanical lock that requires a tool, which is what the BRCOVAN anti-theft knob and the Rokform twist lock provide.

The second is simply taking the phone with you, which takes about a second on a quick-release mount and is why the quick detach feature matters more than most roundups admit. If you ride somewhere genuinely risky, the answer is a mount that combines a bar attachment with a tether or a frame lock, and treating the mount itself as fixed property.

Charge last, not first

Charging is the most over-sold feature in this category, so it is worth being blunt. Wireless charging on a mounted phone adds heat in a place that is already warm, and it will not work through a thick case. A USB-C port in the cradle is the more useful option for most riders, and a wired input lets you run a power supply from a fuse-tapped accessory connector.

If you do want charging while mounted, plan the cable route and the switch before you ride, because a lead that fouls the steering is worse than no lead. Our home studio shock mount guide covers another case where the mounting hardware matters more than the head it holds.

Frequently Asked Questions

The Verdict: Which Handlebar Phone Mount Should You Buy?

If you ride every day and want the least fuss, start with the Lamicall. It is the most widely used clamp here, the lock switch is the single most useful feature on it, and it takes a thick case without an adapter.

If your bike shakes, buy the BRCOVAN with the built-in dampener. If your bike lives outside and you park in public, the BRCOVAN anti-theft aluminium model solves the problem no friction grip can. If your cruiser bars are too crowded for any clamp, the Rokform perch mount puts the phone where you can actually see it.

If you want hardware that survives a decade and a phone you will not have to take off in the rain, the Tackform is the one I would buy twice. The RAM Quick-Grip XL is the pick only when your device is larger than a phone. Whatever you choose, measure the bar first, check the phone depth against the cradle, and fit the dampener only if your riding says you need one.

Whichever mount ends up on your bars in 2026, the test is simple. Ride a full tank, check the screen is readable at a glance in daylight, and confirm nothing touches the throttle or the lever. If all three of those are true, you have made the right call.